Piston and cylinder position is still fine even after 110k. Wonderful machine.
@kilingkiling-tinybell
2 жыл бұрын
Just bought a 2009 ybr 125g turned cafe racer. It just can't climb as fast as I want but other than that I love it. Thank you for this video and more ybr vlogs please. ✌️❤️🇵🇭
@user-vd6is7fg7h
3 ай бұрын
Mine is a 2005 and I just rebuilt it to 150cc. Had to do certain changes to the main jeg and carb needle. Runs good! 30k on the clock. I have it as a hobby and have many tools for it. The engine is easy to deal with, cheap parts and uses little gasoline. I will try to make it last for many more years!
@E6add9
3 ай бұрын
Have fun with the rebuild, you have accomplished what I am planning on doing for the last couple of years now. Still haven’t found some affordable engine case as replacement. But I have not abandoned the project and will get it done eventually.
@user-vd6is7fg7h
3 ай бұрын
@@E6add9 👍 Just remember, if you rebuild to 150cc, it will need a richer mixture. Good luck!😎😎
@ryananthony3351
2 жыл бұрын
110K amazing, my Yamaha ybr 125 has done about 8600 miles and the piston and cylinder are knackered, waiting for new year to get it serviced
@sergecro7652
2 жыл бұрын
Mine has 65k and im always concerned and kinda scared that engine is just gonna stop working one day even tho i change oil regularly. But this video gives me hope and proves that this little engine really is indestructable as they say. So simple, parts really cheap, very economical, the best bike for urban areas for sure!
@E6add9
2 жыл бұрын
Don't be scared, most likely you still have plenty of resource left in your engine! Please check out my current video. I require new engine halves because of worn out gearbox bearing seat. Discovered it after disassembling the engine, it ran fine otherwise..
@hentisof
2 жыл бұрын
my 2,014 ybr got 117,000 km i make overhaul and was totaly diferent i make every oil chancge at 2,500 km and used like 3,000 km every month was full clean inside the only problem i got was valve just cleaded and worked again i make change of all bearings and now is like new prety good motorbyke exep stator failed 3 times changed
@nadjib3ajib268
Ай бұрын
Mine year 2021 i am almost 40 000 km i hope i can reach 100k , its good bike , i may change chain kit soon after reaching 40k km
@tizcoloko
Жыл бұрын
Ybrg in Sonora Mexico 47000 both bars crack, they are more long, this sucks, got the short ones 65000 stator died 76000 cdi blew 98000 valves knocking, replaced 110000 timing chain and new piston, the gear on the crank replaced Still running, maybe is the heat 43 c average
@YAMAHA_FAN_BOi_95
2 жыл бұрын
4:40 that's what she do ❤️
@ThOmAs12111211
2 жыл бұрын
110k is pretty impressive. Any plans on restoring the bearing seats? Seems like the engine held up pretty well. Also, what was your oil change schedule? Did you clock all those km yourself? Was it ridden hard?
@E6add9
2 жыл бұрын
I am currently looking for used engine cases/halves. Too much hassle with restoring the seats. Once I find some, i'll put it back together, with some new bearings. The crakshaft bearings still seem ok, surprisingly. They'll go back into service. I bought the bike back in 2006, it was a demonstrator with only 70km on the clock, so brand new basically. Used it every day, all seasons for a couple of years. Oil change, every 5 thousand km using fully synthetic 10w40 oil. Stay tuned for more vids ;)
@nitroholik7183
Ай бұрын
Yeah
@tonyparker7356
Жыл бұрын
interesting, looks like it survived very well. what made you strip it down?
@E6add9
Жыл бұрын
I found a spare engine for a dime at a scrap dealer, put it in and turned out it runs absolutely well. So i took the chance to inspect the old engine. Have a look at my recent video if you like..
@tonyparker7356
Жыл бұрын
@@E6add9 wow, great result, I will thanks.
@eddmelter1012
Жыл бұрын
mine blew after 25k km but it was secound hand so I cannot say how it was maintained previously
@GermanyBlackdragon
2 жыл бұрын
Ich habe vor bei meiner YBR125 demnächst dass Fahrschulkit samt Sportauspuff für mehr Leistung einzubauen, konnte beides sehr günstig kaufen. Ich habe bis jetzt bei zwei Autos den Zahnriemen gewechselt bin also nicht ganz ahnungslos bei Motoren und ich würde gerne das Kit selbst einbauen. Sehe ich dass richtig dass ich um die Nockenwelle zu tauschen lediglich den Deckel runter nehmen muss, die Kette und das Rad und dann diesen Spanner für die Nockenwelle (Die schwarze Leiste)? Ich würde danach dann natürlich den Ventilspiel nochmal neu auf die Optimalwerte einstellen und mehr müsste es nicht sein oder? Entschuldigung für diese blöde Frage, doch bis jetzt kommten mir nicht viele sonderlich präzise Aussagen zu genau diesem Motor geben^^
@E6add9
2 жыл бұрын
Die Nockenwelle lässt sich seitlich rausziehen, absolut kein Problem. Im Grunde so wie von Dir beschrieben. Pass nur auf beim Zusammenbau, es kann vorkommen, dass die Steuerkette nach dem Spannen neben dem Ritzel auf der Kurbelwelle liegt. Also ein paar mal vorsichtig mit der Nuss an der Kurbelwelle durchdrehen, um zu sehen ob alles passt. Schreib mal, wie viel das Kit wirklich bringt. War vor einiger Zeit noch selbst daran interessiert.
@GermanyBlackdragon
2 жыл бұрын
@@E6add9 Danke für die schnelle Antwort. Auf jeden Fall werde ich vorsichtig sein, beim Zahnriemenwechsel hatte ich auch immer zuerst von Hand gedreht, aber trotzdem danke nochmal für die Warnung. Um die Kette zu spannen kann ich ja dann vorsichtig das Nockenwellenrad samt Kette wieder drauf schieben oder geht dass so nicht? Ich werde bescheid geben sobald ich alles zusammen habe und eine Testfahrt machen konnte. Ich bin auch gespannt, momentan läuft die Maschine so um die 100 glatt. Aber auch nicht wirklich stabil 😅
@hipthehop
Жыл бұрын
Hallo, hast du es schon eingebaut und getestet? Habe auch vor mir über den Winter die Nockenwelle einzubauen.
@GermanyBlackdragon
Жыл бұрын
@@hipthehop Leider musste ich dass Projekt aufgeben. Schon alleine weil mir geraten wurde mit dem großen Führerschein lieber ein großes Motorrad zu besorgen.
@hipthehop
Жыл бұрын
@@GermanyBlackdragon Okay schade, danke für die Antwort
@elkbloodheart1188
3 жыл бұрын
I mean.. If it weren't for the destroyed threads on the engine outside it still looks decent, you could change the rings and might have engine for a while, DISCLAIMER : I don't know shit.
@E6add9
3 жыл бұрын
The threads are not that much of a problem. I have disassembled the engine completely some time ago, to find that the bearing seats are completely worn out. Especially the gearbox bearing seats. I will upload a short video about that in the near future.
@lauriviitala3978
Жыл бұрын
which way should the arrow on the piston be?
@E6add9
Жыл бұрын
The arrow points towards the exhaust side.
@crowdsurfer77
2 жыл бұрын
Dann hat meine ja noch über 100000km zu laufen. 😁
@E6add9
2 жыл бұрын
Absolut :) Guten Start in die Saison!
@crowdsurfer77
2 жыл бұрын
@@E6add9 Danke. Hab Gestern die 10000 geknackt 😁
@onurarc5152
2 жыл бұрын
160k orjinal YBR 125 2012
@E6add9
2 жыл бұрын
Wow, that is impressive! :)
@behlicherif133
2 жыл бұрын
Français
@thomaswilliamfirby180
Жыл бұрын
How many miles is that
@E6add9
Жыл бұрын
Approx. 69000
@tombartram7384
5 ай бұрын
Interesting. 125cc bikes are called a one-two-five in English btw. But a two-fifty is never a two-five-oh.
Пікірлер: 38