I watched the whole video. Adam needs to take a course from an HK Armorer. I’ve had a 91 for 35 years and I’ve spent many hours watching and listening to people who know about these.
@adamsgunroom9331
5 ай бұрын
Link the videos below I’m sure people will appreciate. I never said I was an expert. I built the gun and it didn’t blow up. So I do have that going for me. I made the video because I couldn’t find any video’s on how to do one.
@JoefromSoCal
5 ай бұрын
No hostility intended. Pick up an Armorer’s Manual. Fluted chamber floats the case, which pushes on the bolt, causing the trunnions to push the rollers in, which drives the locking piece back. The bolt carrier moves roughly 4:1 compared the bolt due to carefully engineered ratios/angles. Too much bolt gap, bolt carrier moves too fast. Not enough bolt gap, moves too slow. Cartridges and primers don’t explode. Primers burn with extreme brisance. The powder in a cartridge creates hot, rapidly expanding gases. The HK91 is a blowback, roller delayed. Design. If it was a simple blowback (like a 9mm handgun) the bolt would have to weigh 35 lbs. There’s much, much more to know. For the last 35 years I’ve searched for everything I could find. That’s how I found your video. Good luck with your channel. 👍
@HarborSite-7
Жыл бұрын
Great explanation here and very important information for people to be able build something that is safe to operate. 👍
@adamsgunroom9331
Жыл бұрын
Thanks
@HarborSite-7
Жыл бұрын
@@adamsgunroom9331 Not everyone can even grasp these concepts, nevermind explain them. I've seen some CETME build videos that show some bad info and building techniques that are really questionable or just flat out wrong, which can be dangerous to the viewers. I think it's important that if you're going to put this stuff out here that it's correct. I think yours is exceptional. So thank you.
@gdreclaimed5442
2 жыл бұрын
Nice job explaining! I also like the microphone you are using.
@adamsgunroom9331
2 жыл бұрын
Thanks
@renelopez2244
2 жыл бұрын
Can you do a range review? Just some down range shooting and maybe An accuracy test on this. Would be fun to see it in action
@adamsgunroom9331
2 жыл бұрын
I can give it a try. I am not the best at doing videos but I will do my best. Lol
@renelopez2244
2 жыл бұрын
@@adamsgunroom9331 Sounds good.. Thanks
@jyterliper
2 жыл бұрын
Thanks for this info building one myself and having a hard time on this part. Should I press the barrel in the trunnion before welding it in the receiver. Also did you weld the receiver take down pins in from the inside or the outside?
@adamsgunroom9331
2 жыл бұрын
You could press the barrel first but I welded the trunion into the receiver then pressed it in. I would weld the pins on the inside of the receiver. If you dimple the sheet metal in on the receiver you could weld it on the outside as well.
@jacobthayer5997
Жыл бұрын
Is it normal for HK33 clones to show a minor but visible bulge at the base of the case? I have a Coharie CA53 pistol and I'm having a few issues. It's my first roller delayed firearm. The bulge concerns me, but it is also having ejection issues, the spent casing and the next round double feed. Sometimes it doesn't extract at all. Any advice is appreciated.
@adamsgunroom9331
Жыл бұрын
Bulge is concerning as it sounds like you are going to have a case failure. you might have too much bolt gap or a headspace problem.
@tux8664
Жыл бұрын
Case bulging is seen as normal, but still probably able to be improved
@loy4341
2 жыл бұрын
What should I do if my bolt gap is literally non existent? In other words, how can I increase bolt gap (apart form buying new parts)?
@adamsgunroom9331
2 жыл бұрын
The only thing you can do is to drive out the barrel pin or press it out. Press out the barrel from trunnion turn your barrel 180 degrees. repress with proper bolt gap and then pin the barrel again. I think this is the best fix for your situation. I would take apart the bolt and measure the rollers for excessive wear. I would also check the locking piece for excessive wear as well. Good luck sounds like a fun project!
@oso9809
11 ай бұрын
Could you not purchase larger rollers? +4,+6????
@epicgangnamstyle8783
2 жыл бұрын
So a TL;DR is that if I were to get everything aligned properly, the bolt should close on a 7.62 NATO go gauge, not close on a no-go gauge, and also have ~0.00010" of a gap between the rear of the bolt and the front of the carrier?
@adamsgunroom9331
2 жыл бұрын
Not exactly because there could be some tolerance stacking occurring with the bolt itself. Headspace would be measured from bolt face to datum line in chamber. I wouldn’t use gap off back of carrier.
@metaldave556
Жыл бұрын
has anyone taken a century arms c308 and put all hk innards in it? id imagine thered be small differences but i also heard that the c308s were bent on the same jig that does g3's as well.
@adamsgunroom9331
Жыл бұрын
The trunions are different so they are not interchangeable
@metaldave556
Жыл бұрын
@@adamsgunroom9331 ah damn, i knew i shouldve waited until i got a reply. i literally just dropped a bunch of money on a new bolt carrier, bolt head, firing pin and spring. do you know how different in spec the trunnion is? could it be corrected with larger rollers? i know theres lots of mixed opinions on this, but i want to suppress it. i got the 36° locking piece and wanted to make sure my bolt gap is in spec, but seeing how the trunnion is different, i dont want to blow my rifle up and probably myself in the process.
@numbsliwa
9 ай бұрын
hello everyone. I have recently acquired a CETME C and would like to know the production date by the serial number. where can i find this out. and I noticed that my rifle does not have these bulges for mounting optics. do you know why?
@adamsgunroom9331
8 ай бұрын
I honestly don’t know why.
@norincokid
2 жыл бұрын
I like it, but where is your rear sight??
@adamsgunroom9331
2 жыл бұрын
I didn’t use it. If I want to shoot irons I left enough room to add it later in front of the rail I welded to the receiver.
@squinones9002
Жыл бұрын
What's the best way to reach you?
@adamsgunroom9331
Жыл бұрын
Through the comment section
@muffinman3111
Жыл бұрын
How hard is it to build a cetme ?
@adamsgunroom9331
Жыл бұрын
It’s not too bad if your mechanical. You will need some tools so if you don’t have a welder, hydraulic press, drill or drill press. It’s cheaper to just buy a ptr. Otherwise take your time and it’s totally possible
@Gatsu3D2A
Жыл бұрын
I just built a working 3d printed one using surplus parts not too hard
@oso9809
11 ай бұрын
I will add it’s the cheapest build as well, so if it goes bad you are not out a huge pile of cash.
@joemiller5110
Жыл бұрын
Taking way too long to get to your topic. Sorry dude
@Imissthefuhrer
Жыл бұрын
How would you go about reducing bolt gap? Getting light primer strikes and such.
@adamsgunroom9331
Жыл бұрын
You can use negative rollers for example you can buy -3 rollers or you can pull the barrel pin turn 180 degrees repress and pin the barrel to proper spec
Пікірлер: 38